PNEUMATIC INLINE POWDER SAMPLER JAM PROOF

PNEUMATIC controlled Iinline powder sampler
PNEUMATIC INLINE POWDER SAMPLER JAM PROOF
WHITESTONE VA
TEL (804) 318-3686 FAX (703) 991-7133
[email protected] 
WWW.QCLABEQUIPMENT.COM
Copyright 2012: QAQC Lab | Particle Measurement System | All rights reserved.
804-318-3686 | [email protected]
freeglide pneumatic powder sampler
675 FG1000A      100 mm DIAMETER PIPE AUTOMATIC SAMPLER

675 FG1500A      150 mm DIAMETER PIPE AUTOMATIC SAMPLER

675 FG2000A      200 mm DIAMETER PIPE AUTOMATIC SAMPLER

675 FG3000A      300 mm DIAMETER PIPE AUTOMATIC SAMPLER
​MATERIALS OF CONSTRUCTION

Contact parts:        - 316 stainless steel
                              - PTFE
                              - Silicone rubber, Viton or EPDM
                              - Other materials on request

Non contact parts: - 304 grade stainless steel
                              - Other materials as required.
The Pneumatic Inline Powder Sampler is specially designed and engineered so that powder is kept out of the bearings by a special flexible membrane - this means the sampler will not jam

The sample is collected in a cup and so is not physically altered by the sampling process
When the sampling cup is retracted, the full bore of the downpipe is available for powder flow

Made from FDA acceptable materials and is easy to strip down for cleaning
freeglide pneumatics
INLINE POWDER SAMPLER
AUTOMATIC OPERATION
PIPE DIAMETER 100mm to 300mm
675 FG (xxx m/a)
logo
logo
EQUIPMENT FOR QUALITY CONTROL AND R&D 
www.qclabequipment.com
Telephone      (804) 318-3686
Toll Free US   (866) 244 1578
Fax                   (703) 991-7133
Hours      8 AM - 6 PM EST
INTERNATIONAL & DOMESTIC SALES
CUSTOMER SERVICE * SALES * TECHNICAL SUPPORT


DELIVERIES WORLDWIDE

PERFORMANCE GUARANTEE
inline powder sampler schematic
OPERATION

Resting

When the sampler is not in use the full bore of the downpipe is
available for powder flow.

Sampling

The sampling cup is extended into the downpipe to catch the
product as it falls.

Discharging

The sampling cup is then retracted and inverted. The powder
sample falls down the discharge chute to where it is collected
pneumatic freeglide sampler for powders
freeglide pneumatics
Confirm that there is an earthing route from the cup to the Tee Piece (see section 5.3)
Confirm that there is an earthing route from the Tee Piece to the downpipe (see section 5.4)
Visually check that the sampler is making a good seal with the inside face of the product chute when 
in the extended and retracted positions.

* Polymer components must be viewed as consumable parts and replaced at the first signs of wear.

Lubrication schedule
There are no components on this sampler assembly which require lubrication.

5.3 Earthing (Grounding) Check – Inside Sampler
Ensure that the resistance between the cup and the Tee Piece is less than 1 Ohm.
The FreeGlide is fitted with phosphor bronze bearings; these provide a constant metal to metal earthing path 
through the equipment. There is no adjustment possible by the the customer. 

If the resistance is greater than 1 Ohm, then the inner workings of the sampler are electrically isolated. 
The device must not be reinstalled until it has been properly investigated. 

Earthing (Grounding) Check – to surrounding equipment
Ensure that the resistance between the Tee Piece and the Downpipe (i.e.
surrounding equipment) is less than 1 Ohm.
The automatic sampler uses pneumatics to extend and retract the cup and to rotate it. Electrical sensors are used to monitor the position of the automatic sampler .
freeglide pneumatic powder sampler
INSTALLING THE FRONT BOSS
ELECTRICAL CONNECTIONS
SAMPLE MANUAL FOR AUTOMATIC FREEGLIDE
NON VERTICAL INSTALL
inline sampler parts
CHOOSING THE RIGHT SIZE

visa mc logo
DOWNLOADS
"The general consensus is that only sampling
from a bulk powder while it is in motion can
yield the desired representative sample."
BROCHURE FREEGLIDE INLINE POWDER SAMPLER
STORE SEARCH
BROCHURE

QUICK QUOTE
Recommended maintenance

In order to keep the sampler in good working order,
regular maintenance is required,
and this should be recorded and kept as a record.

All maintenance personnel who carry out the maintenance
on the sampler should be fully qualified.

Recommended weekly maintenance

Visually inspect the Diaphragm for wear*
Visually inspect the Closing Plug for wear*
Visually inspect the Quadrings for wear*
Inspect filters for damage
SELECTION OF BLANKING PLATE
blanking plate
The blanking plate is a 316 SS Plate that
fits in to the front boss, while the sampler 
is being serviced. Two styles are available